- 您现在的位置：买卖IC网 > Sheet目录1251 > UM232H (FTDI, Future Technology Devices International Ltd)MOD USB HS FT232H EVAL
Document Reference No.: FT_000367
UM232H Single Channel USB Hi-Speed FT232H Development Module Error!
Unknown document property name.
Datasheet Version 1.3
Clearance No.: FTDI# 198
the output of the 3.3V regulator and the external 3.3V logic or power VIO from the 3V3 pin of the
FT232H.
7.3 Self Powered Configuration
7.3.1 Self-Powered Configuration with 3V3 I/O and running on +5V external supply:
Figure 7.3 : Self-Powered Configuration – 5V0 External Supply
Figure 7.3 illustrates the UM232H in a typical USB Self-Powered configuration. An external supply +5.0V is
connected to the module ’s 5V0 pin. J2-2 (VIO) is also connected to J2-3 (3V3) to supply the VCCIO supply
from the on board regulator but a separate supply could have been used.
A USB Self Powered device gets its power from its own power supply and does not draw current from the
USB bus. The basic rules for USB Self powered devices are as follows:
i) A Self Powered device should not force current down the USB bus when the USB Host or Hub
Controller use powered down.
ii) A Self Powered Device can use as much current as it likes during normal operation and USB suspend
as it has its own power supply.
iii) A Self Powered Device can be used with any USB Host and both Bus and Self Powered USB Hub. In
this case, the power descriptor in the internal EEPROM should be programmed to a value of zero
(Self-Powered).
In order to meet requirement (i) the USB Power is used to control the RESET# Pin of the FT232H device.
When the USB Host or Hub is powered up the internal 1.5kΩ resistor on USBDP is pulled up to 3.3V, thus
identifying the devices as a full speed device to USB. When the USB Host or Hub Power is off, RESET# will
go low and the device will be held in reset. As RESET# is low, the internal 1.5kΩ resistor will not be pulled
up to 3.3V, so no current will be forced down USBDP via the 1.5kΩ pull -up resistor when the host or hub is
powered down.
To do this J1-3 (USB) is connected to PU2 and PU1 is connected to J2-4 (RST#). Failure to do this may
cause some USB host or hub controllers to power up erratically.
Note: When the FT232H is in reset, the UART interface pins all go tri- state. These pins have internal 200kΩ
pull-up resistors to VCCIO, so they will gently pull high unless driven by some external logic.
Figure 7.3 is also an example of interfacing the FT232H to a Microcontroller (MCU) UART interface. This
example uses TXD and RXD for transmission and reception of data and RTS# / CTS# hardware
handshaking.
18
? Copyright 2012 Future Technology Devices International Ltd
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
UM232R
MOD USB UART DEV FT232R
UM245R
MOD USB PARALLEL FIFO DEV FT245R
UMTS 2
FUSE 2A 250V TLAG IEC SMD
UPG1-4-61-303-01
MAGNETIC CIRC BRKR SP 30A TOG SW
UPL111-1-60-503
MAGNETIC CIRCUIT PROTECTOR 50A
UPL2000-D1/B
BNC PLUG CRIMP STR 7538CBL 50/PK
UPL2000-D20/B
BNC PLUG CRIMP STR 1505F 50/PK
UPL220-009
BNC PLUG FULL CRIMP STR 8218CBL
相关代理商/技术参数
UM232H-B
制造商:Future Technology Devices International (FTDI Chip) 功能描述:BRD BREAKOUT USB HS FT232H 制造商:Future Technology Devices International (FTDI Chip) 功能描述:Development Module for FT232H with a Female Connector
UM232H-B-01
功能描述:界面开发工具 USB to Serial/Paral. Break-out Board
RoHS:否 制造商:Bourns 产品:Evaluation Boards 类型:RS-485 工具用于评估:ADM3485E 接口类型:RS-485 工作电源电压:3.3 V
UM232H-B-NC
功能描述:界面开发工具 USB to Serial/Paral. Break Out Board
RoHS:否 制造商:Bourns 产品:Evaluation Boards 类型:RS-485 工具用于评估:ADM3485E 接口类型:RS-485 工作电源电压:3.3 V
UM232H-B-WE
功能描述:界面开发工具 USB to Serial/Paral. Break Out Board
RoHS:否 制造商:Bourns 产品:Evaluation Boards 类型:RS-485 工具用于评估:ADM3485E 接口类型:RS-485 工作电源电压:3.3 V
UM232M
制造商:未知厂家 制造商全称:未知厂家 功能描述:Analog IC
UM232R
功能描述:界面开发工具 USB to Serial UART Dev Mod for FT232R RoHS:否 制造商:Bourns 产品:Evaluation Boards 类型:RS-485 工具用于评估:ADM3485E 接口类型:RS-485 工作电源电压:3.3 V
UM233
制造商:未知厂家 制造商全称:未知厂家 功能描述:Analog IC
UM233M
制造商:未知厂家 制造商全称:未知厂家 功能描述:Analog IC